-آلة اختبار العالمي, آلة اختبار تأثير-

الاحتكاك آلة اختبار ارتداء

» الاحتكاك آلة اختبار ارتداء

  • MRC-1 FZG جير ارتداء آلة اختبار

    الفئة وTAGS:
    الاحتكاك آلة اختبار ارتداء

    FZG آلة اختبار ارتداء والعتاد هو اختبار آلة متعددة الأغراض. يمكن استخدامها لتقييم القدرة الاستيعابية للزيوت التشحيم, كما يمكن الخاصة التي أدلى بها مطالب العميل. وعادة ما تستخدم لمعدات الانحناء قوة التعب واللمس والعتاد اختبار قوة التعب.

     

    تحقيق
    • وصف المنتج
    • المعايير
    • ظروف العمل
    • working principle

    مقدمة مختصرة

    FZG آلة اختبار ارتداء والعتاد هو اختبار آلة متعددة الأغراض. يمكن استخدامها لتقييم القدرة الاستيعابية للزيوت التشحيم, كما يمكن الخاصة التي أدلى بها مطالب العميل. وعادة ما تستخدم لمعدات الانحناء قوة التعب واللمس والعتاد اختبار قوة التعب.
    II. التقدم بطلب للحصول:
    يؤكد هذا الجهاز لGB / T 13672-92 طريقة الاختبار القياسية لالجرجرة الحمولة من التروس وSH / T 0366-1992 زيوت التشحيم طريقة اختبار القدرة على التحمل (CL-100 طريقة آلة جير)
    III. المواصفات الفنية:
    مواصفات MR-C1
    ماكس. عزم الدوران 1Kn. م
    ماكس. الطبقة تحميل 13 الطبقات
    دقة التحكم في درجة الحرارة ± 2 ℃
    قوة المحرك 6.5 / 8KW
    سرعة المحرك 1450/2880 دورة / دقيقة
    علبة تروس حجم 1.25L
    طاقة التسخين 0.5X3 = 1.5KW
    أبعاد 1390X750X1082mm

    GB / T 13672-92
    Standard test method for scuffing load capacity of gears

    SH/T 0306-1992
    Lubricant carrying capacity test method (CL-100 طريقة آلة جير)

    DIN ISO 14635-1-2006
    Gears-FZG test procedures-Part 1: FZG test method A/8,3/90 for relative scuffing load-carrying capacity of oils

    GB / T 14229-93
    Standard of test method for surface load capacity of gears

    GB / T 14230-93
    Standard of test method for bending load capacity of gears

    1> The fluctuation range of the power supply voltage should not exceed the rated value ± 10% and the fluctuation range of the frequency should not exceed 2% of the rated value.
    2>Test machine should be installed horizontally and the installed base should be smoothly. The horizontal error for the host workbench aspect direction should not exceed 0.2/1000.
    3>Room temperature 10 º C-35 º C.
    4>The environment no vibration, no strong magnetic interference and non-corrosive media.
    5>Relative humidity less than 80%.

    1> وضع تحميل
    This machine is a dynamic closed-loop configuration, and load mode adopts rod hanging weights mode.
    The loading lever is hung on the load sheave clutch. By hanging weights plus through fastening loaded clutch nut and make the two sheave tighten which installed on the loaded clutch. Then remove the weights and the loading lever and you can readout the torque on the clutch torque measurement.

    3> Installation and adjustment
    Make the test machine at the level of the floor and mat three horns. Put the spirit level on the test table. By adjusting the horn to make the vertical and horizontal direction error do not exceed 0.2/1000.
    The test machine host should be placed separately from the control cabinet to avoid the noise and pungent odor when the testing machine working. After the start of the test machine, person can not inter into the room which the machine placed.
    The test procedure in accordance with the the "lubricant carrying capacity assay (CL-100 gear machine method) SH/T0306-92" provisions.

    نموذج الاستفسار (ونحن سوف نعود اليكم في اسرع وقت ممكن)

    اسم:
    *
    البريد الإلكتروني:
    *
    رسالة:

    التحقق:
    4 + 6 = ?

    ربما تريد أيضا

  • فئات المنتجات

  • سهم إلى صديق